OMNIA H

 > EXTERNAL UNIT CHARACTERISTICS OMNIA H-UE:

Reduced starting current thanks to Inverter technology

Compressor with twin rotary DC INVERTER motor positioned on rubber anti-vibration mounts and wrapped by a double layer of sound-absorbing material to reduce vibrations and noise

The compressor is also equipped with crankcase oil heater

Bi-flow electronic expansion valve

4-way valve

Axial fans with DC brushless motor complete with safety protection grilles

Finned coil consisting of copper pipes and aluminum fins

External air temperature probe already installed on the unit

DHW tank water temperature sensor supplied as standard (installed by the installer)

> INTERNAL UNIT CHARACTERISTICS OMNIA H-UI:

Available with 3kw electrical integration (OMNIA HI-UI) or without integration (OMNIA H-UI)

Hydraulic unit with 3-way diverter valve for DHW production supplied as standard

Brazed stainless steel water / gas plate heat exchanger

Low consumption system circulator with DC brushless motor

Automatic air vent

Water differential pressure switch

Water pressure gauge

Expansion vessel

Safety valve

Y-shaped water filter supplied as standard (installed by the installer)

> THE CONTROL SYSTEM

The user interface consists of a wired remote controller (up to 50 m from the unit) which allows the management of:

- HEATING AND COOLING SYSTEM, where the heat pump is the sole energy source. The unit, if activated in heat or cool mode, works by modulating the frequency of the compressor to maintain the temperature of the produced water to the setpoint value set by the controller. Through parameter you can use the remote controller (eg. For single-zone systems) as a room thermostat.

- DOMESTIC HOT WATER PRODUCTION (DHW). The unit is activated in a heatt mode to keep the temperature of a DHW tank (not supplied) to the setpoint value. It requires a 3-way diverter valve (not supplied) and a temperature sensor (T5 probe, L = 10m, provided) to be inserted into one well of the DHW tank.

- ADDITIONAL SOURCES OF ENERGY (boiler or electrical heater). Depending on the parameters set, these sources can be activated in integration or replacement of the heat pump when the system is used for space heating or for DHW production.

The controller also activate additional energy sources in case the heat pump is not working.

- ELECTRIC HEATER OF THE DHW TANK. The controller can manage the activation of  an electric heater inserted in the DHW tank as a heat integration to the heat pump, for disinfecting function, or as a source of energy reserve for DHW production in case the heat pump is not working.

FAST DHW. This function can be activated manually and it allows you to give priority to DHW production by activating all energy sources (heat pumps, electric heaters, boiler) available for DHW heating to bring in the shortest time possible the DHW tank to the setpoint required.

- DISINFECT FUNCTION. You can set from the controller weekly cycles for disinfecting the water in the Dhw tank. In order to successfully execute these cycles, the heat pump must be integrated with DHW electric heater or boiler.

- SILENT MODE. If active it allows a reduction of the maximum frequency of the compressor and of the fan speed in order to reduce the noise emitted and the power absorbed by the unit. There are 2 levels of silencing. Through time programming, you can define for 2 daily time bands the desired silent level (eg. during the night).

- ON / OFF using an external contact. The unit can be turned on and off (eg. thermostat / remote switch) via an external contact: in this case the unit will operate in the mode set by the controller keyboard.

- HEAT / COOL via external contacts. The unit can be activated in heat or cool mode via two external contacts (eg. thermostat that manages the heat and cool demand / remote switch).

- ECO MODE. Possibility to define in heat mode a time band within which the heat pump works with a sliding setpoint defined by the chosen climatic curve. 8 climatic curves are available for low temperature systems (radiant floor) and 8 climatic curves for fan coil or radiator systems)

- WEEKLY SCHEDULING. It allows a schedulation of 6 time bands for each day of the week: for each time band it is possible to define the mode (COOL / HEAT / DHW) and the required  setpoint.

- Detailed alarms diagnostics with alarms history.

- Display of all operating parameters.